Scientific Atlanta EXPLORER 2000 User's Guide download pdf

Inserting the Batteries

Procedure

Your remote control requires two AA

alkaline batteries.

CAUTION:

Make sure you correctly align

the positive (+) and negative (-)

terminals on the batteries to the

corresponding terminals in the

remote control.

ER1 Remote Control Quick Reference

1. Press forward then lift up on the

lever on the back cover of the

remote control. The battery cover

releases, and you can pull the

cover up to remove it.

T6434

3. Insert and firmly seat two new AA

batteries (alkaline required) into

the battery compartment.

4. Slide the front of the battery cover

back onto the remote control and

snap the back of the cover into

place.

T6436

2. Remove and safely dispose of the

old batteries.

T6435

T8101

To Program for Volume Control

You can program the remote control

to control the volume and mute

functions through the EXPLORER

2000 DHCT, or through your TV.

The default is through the TV.

1. Point the remote control away

from the EXPLORER 2000 DHCT,

the TV, and the VCR.

2. Press and hold the CBL key and

the SELECT key at the same time,

until the LED on the remote

control blinks twice.

3. Using the remote control keypad,

enter 993. The LED on the remote

blinks twice.

4. Press the TV key or the CBL key,

depending on which device you

want to control the volume. The

LED on the remote control blinks

twice to confirm a valid selection.

5. Point the remote toward the

device on which you chose to

control the volume, and adjust the

volume to confirm operation.

To Identify Programmed Codes

You can find out which code you

used to program your TV or VCR.

You can determine the code by

counting the number of times the

LED blinks during the following

procedure.

1. Point the remote control away

from the EXPLORER 2000 DHCT ,

the TV, and the VCR.

2. Do one of the following:

• To identify the TV code, press

and hold the TV key and the

SELECT key at the same time

until the LED on the remote

control blinks twice, or

• To identify the VCR code, press

and hold the VCR key and the

SELECT key at the same time

until the LED on the remote

control blinks twice.

3. Using the remote control keypad,

enter 990. The LED on the remote

blinks twice.

4. Press 1 on the keypad; then,

count the LED blinks. The

number of blinks indicates the

first number in the code. For

example, 4 blinks indicates the

first number in the code is 4.

5. Press 2 on the keypad; then,

count the LED blinks. The

number of blinks indicates the

second number in the code.

6. Press 3 on the keypad; then,

count the LED blinks. The

number of blinks indicates the

third number in the code.

7. Write down the code in the table

provided for future reference.

Identifying Codes Controlling Volume

Model ER1

Remote Control

User’s Guide

POWER

SELECT

VOL

–

INFO

GUIDE

–

Record of Codes

Record your setup codes

in the following table.

CBL

VCR

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This device

may not cause harmful interference, and

(2) this device must accept any interference

received, including interference that may

cause undesired operation.

Note: This equipment has been tested and

found to comply with the limits for a class

B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to

provide reasonable protection against

harmful interference in a residential installa-

tion. This equipment generates, uses, and

can radiate radio frequency energy and, if

not installed and used in accordance with

the instructions, may cause harmful inter-

ference to radio communication. However,

there is no guarantee that interference will

not occur in a particular installation If this

equipment does cause harmful interference

to radio or television reception, which can

be determined by turning the equipment

off and on, the use is encourage to try to

correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and the receiver.

• Connect the equipment into an outlet on

a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

Any changes or modifications not expressly

approved by Scientific-Atlanta could void

the user’s authority to operate this

equipment.

United States: Scientific-Atlanta, Inc.

4261 Communications Drive

P.O. Box 6850, Norcross, GA 30091-6850

Tel: 770.903.5000 TWX: 810.799.4912 Telex: 0542898

Europe: Scientific-Atlanta Europe, Ltd. Home Park

Estate, Kings Langley, Herts WD4 8LZ, England

Tel: +44.1.923.266133 Fax: +44.1.923.269018

Asia-Pacific: Scientific-Atlanta (HK), Ltd. Suite 56-57,

5/F New Henry House, 10 Ice House Street, Central,

Hong Kong Tel: 852.2522.5059 Fax: 852.2522.5624

Printed in USA September 1999 Part Number 716360 Rev B

FCC Compliance

Power

DHCT on or off

VCR on or off

TV on or off

LED

Sound

Mutes sound

Adjusts volume

Device Control

Switches control between

your VCR and Video On

Demand (VOD) program

Controls your VCR’s

TV/VCR function.

Controls the BYPASS

option (See Optional

Bypass Feature)

Channels

Displays channel

information

Selects channels, up or

down

Enter channel numbers

(also used to enter your

personal identification

number [PIN] for

parental control)

Views favorite channels

Returns to last channel

viewed

VCR/VOD

Fast forwards VCR/VOD

Records VCR program

Stops VCR/VOD

Rewinds VCR/VOD

Plays VCR/VOD

Pauses VCR/VOD

Screens

Pages Up/Pages Down

Hides interactive screen

Makes on-screen

decisions

Displays interactive

program guide

Displays DHCT settings

Moves through interactive

screen choices

Chooses interactive

screen item

Notes:

• Program the remote control

before you use the DHCT. See

Programming the Remote

Control for programming

procedures.

• Make sure you use only alkaline

batteries in the remote control. See

Inserting the Batteries for more

information.

1 2

Model ER1 1
Remote Control 1

Summary of Contents

Page 1 - Remote Control

Inserting the BatteriesProcedureYour remote control requires two AAalkaline batteries.CAUTION:Make sure you correctly alignthe positive (+) and negati

Page 2

TV Setup Codes VCR Setup CodesAdmiral—107Adventura—060Aiko—106Akai—044Alaron—193Ambassador—191Anam—194Anam National—069, 194AOC—033, 044, 199Audiovox—